| |
| |
| Hubs and Switches - ENHGS-224 |
 This ENHGS-224 is a powerful, high performance Gigabit Ethernet switch, providing smart and efficient management functions and able to support 26 active connections, where 24 ports of them are capable of serving connections at 10/100 Mbps, while the other two are capable of connecting at 10/100/1000 Mbps with Full/Half Duplex capability. The switch also supports features such as speed/duplex/flow control, ports trunk (port aggregation), port-based/802.1Q VLAN configurations, bandwidth control features, port mirroring functions and also some other miscellaneous functions. Store-and-forward switching mode promises the low latency and eliminates all the network errors, including runt and CRC error packets. Under Full duplex mode, the transmission and reception of network frames can occur simultaneously without causing collisons. This mode will also doubling the network bandwidth as well. The switch is plug-n-play enabled. Without any manual configuration, the device is compatible with all kinds of network protocols. Morever, the rich diagnostic LEDs on the front panel allow user to monitor the overall operating status of the system.
|
| Key Features |
Specifications |
- Complies with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3x, IEEE 802.3ad and IEEE 802.1Q standard.
- 24 (RJ-45) ports for 10Base-T /100Base-TX, and 2(RJ-45) ports for 1000Base-T connectivity.
- All 24 10/100 Mbps ports support NWay protocol for speed(10/100Mbps) and duplex mode(Half/Full) auto-detection.
- The Gigabit ports supports NWay protocol for speed(10/100/1000Mbps) and Full-duplex mode only.
- All ports support auto MDI/MDI-X function on all ports. one RS-232 port is provided for console management.
- Supports up to 6 group of vLAN function and up to 7 groups of port trunk function.
- Wire-speed packet filtering and forwarding rate.
- Store-and-forward architecture filters fragment & CRC error packets.
- Supports 6K MAC address entries in whole system. 384 KBytes buffer memory.
- 19" standard rack-mountable design
- Supports extensive LED indicators for network diagnostics.
- Internal universal switching power supply(90-246VAC / 47-63 Hz).
- FCC Class A, CE
|
Standard:
IEEE 802.3, IEEE 802.3u, IEEE 802.3x, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.1Q
Interface:
24* 10/100Mbps RJ-45 NWay ports
2* 10/100/1000Mbps, RJ-45 ports
NWay Protocol Support:
Network Speed: 10/100/1000Mbps Duplex mode: Full & Half (10/100Mbps); Full(1000Mbps)
Link Aggregation (Port Trunking):
7 group of link aggregation at the same time
Console Port (RS-232 port):
Fix Baud Rate 9600, One Stop Bit, 8-Bit Data Transfers, None Parity Check Bit
Buffer Memory / MAC Address Table:
384 KByte for the whole system / 6K entries
Filtering / Forwarding Rate:
10Mbps: 14,880pps / 14,880pps
100Mbps: 148,800pps / 148,800pps
1000Mbps: 1,488,100pps
Emission:
FCC Class A, CE
Rich LED Indicators:
System: Power, 100M, speed/Link/Activity, 10M, 100M, 1000M, TX;RX, FDX/COL
Operating Temperature:
0~50 Celsius Degree (32~122 Farenheit Degree)
Operating Humidity:
10% ~ 90% (non-condensing)
Dimension / Power Supply:
400 x 192 x 39 mm (Length x Width x Height)
90-264 VAC/ 47-63 Hz |
|
|
| |
Ethernet Cards